Tag Archives: shaft 2018

China supplier 2018 Hot Sale 40-65HP Farming and Transportation Use 2WD or 4WD Drive Four Wheel Tractor Weituo Brand Aoye Series Shaft Transmission with high quality

Merchandise Description

AOYE series tractor is with electrical power ranged from 40HP to 65HP.
The AOYE series tractors is with potent diesel motor, hydraulic steering, dual stage clutch, 8+4 gearbox and dual speed PTO.
The tractors can be with driving cabin, which can be matached with AC, fan, heater and many others.
Make sure you speak to for details of every design.  
 

 Model AOYE-404 AOYE454 AOYE504 AOYE554 AOYE604 AOYE654
 Type   4×4         4WD
   Length 3868
    Width 1614
    Depth 2330
(mm)  Wheel base  Front wheel 1150-1450
 Main Dimensions of Tractors   Rear wheel 1300-1500
Tread 2007
 Min. Ground Base 305
(kg)Dry Mass 1680-1840
Engine  Model 490 4100 4105
 Type  Vertical, 4-cylinder, Water Cooled and 4-stroke
(kw)      Rated Power  29.4 33.1 36.8 40.4 44.1 47.8
(r/min)Rated Rev. 2400
Fuel   Diesel Oil
Tyre  Front Wheel 8.30-24
Rear Wheel 12.4-28
 Clutch Dry-friction, Dual Stage or Dry-friction, Two Stage
Steering  Hydraulic Type
Transmission Box (4+1)×2 or(4+1)×2×2(with creeper)
Suspension Type  Post Postitioned Tri-point Suspension Catalogue 2
  PTO Shaft (r/min)Type and Rev.  Non-independent Type 540/1000, 540/720  
  
 Spline Size              
I35 Rectangle Spline with 6 teeth
 Model AOYE-404 AOYE454 AOYE504 AOYE554 AOYE604 AOYE654
 Type   4×4         4WD
   Length 3868
    Width 1614
    Depth 2330
(mm)  Wheel base  Front wheel 1150-1450
 Main Dimensions of Tractors   Rear wheel 1300-1500
Tread 2007
 Min. Ground Base 305
(kg)Dry Mass 1680-1840
Engine  Model 490 4100 4105
 Type  Vertical, 4-cylinder, Water Cooled and 4-stroke
(kw)      Rated Power  29.4 33.1 36.8 40.4 44.1 47.8
(r/min)Rated Rev. 2400
Fuel   Diesel Oil
Tyre  Front Wheel 8.30-24
Rear Wheel 12.4-28
 Clutch Dry-friction, Dual Stage or Dry-friction, Two Stage
Steering  Hydraulic Type
Transmission Box (4+1)×2 or(4+1)×2×2(with creeper)
Suspension Type  Post Postitioned Tri-point Suspension Catalogue 2
  PTO Shaft (r/min)Type and Rev.  Non-independent Type 540/1000, 540/720  
  
 Spline Size              
I35 Rectangle Spline with 6 teeth

Guide to Drive Shafts and U-Joints

If you’re concerned about the performance of your car’s driveshaft, you’re not alone. Many car owners are unaware of the warning signs of a failed driveshaft, but knowing what to look for can help you avoid costly repairs. Here is a brief guide on drive shafts, U-joints and maintenance intervals. Listed below are key points to consider before replacing a vehicle driveshaft.
air-compressor

Symptoms of Driveshaft Failure

Identifying a faulty driveshaft is easy if you’ve ever heard a strange noise from under your car. These sounds are caused by worn U-joints and bearings supporting the drive shaft. When they fail, the drive shafts stop rotating properly, creating a clanking or squeaking sound. When this happens, you may hear noise from the side of the steering wheel or floor.
In addition to noise, a faulty driveshaft can cause your car to swerve in tight corners. It can also lead to suspended bindings that limit overall control. Therefore, you should have these symptoms checked by a mechanic as soon as you notice them. If you notice any of the symptoms above, your next step should be to tow your vehicle to a mechanic. To avoid extra trouble, make sure you’ve taken precautions by checking your car’s oil level.
In addition to these symptoms, you should also look for any noise from the drive shaft. The first thing to look for is the squeak. This was caused by severe damage to the U-joint attached to the drive shaft. In addition to noise, you should also look for rust on the bearing cap seals. In extreme cases, your car can even shudder when accelerating.
Vibration while driving can be an early warning sign of a driveshaft failure. Vibration can be due to worn bushings, stuck sliding yokes, or even springs or bent yokes. Excessive torque can be caused by a worn center bearing or a damaged U-joint. The vehicle may make unusual noises in the chassis system.
If you notice these signs, it’s time to take your car to a mechanic. You should check regularly, especially heavy vehicles. If you’re not sure what’s causing the noise, check your car’s transmission, engine, and rear differential. If you suspect that a driveshaft needs to be replaced, a certified mechanic can replace the driveshaft in your car.
air-compressor

Drive shaft type

Driveshafts are used in many different types of vehicles. These include four-wheel drive, front-engine rear-wheel drive, motorcycles and boats. Each type of drive shaft has its own purpose. Below is an overview of the three most common types of drive shafts:
The driveshaft is a circular, elongated shaft that transmits torque from the engine to the wheels. Drive shafts often contain many joints to compensate for changes in length or angle. Some drive shafts also include connecting shafts and internal constant velocity joints. Some also include torsional dampers, spline joints, and even prismatic joints. The most important thing about the driveshaft is that it plays a vital role in transmitting torque from the engine to the wheels.
The drive shaft needs to be both light and strong to move torque. While steel is the most commonly used material for automotive driveshafts, other materials such as aluminum, composites, and carbon fiber are also commonly used. It all depends on the purpose and size of the vehicle. Precision Manufacturing is a good source for OEM products and OEM driveshafts. So when you’re looking for a new driveshaft, keep these factors in mind when buying.
Cardan joints are another common drive shaft. A universal joint, also known as a U-joint, is a flexible coupling that allows one shaft to drive the other at an angle. This type of drive shaft allows power to be transmitted while the angle of the other shaft is constantly changing. While a gimbal is a good option, it’s not a perfect solution for all applications.
CZPT, Inc. has state-of-the-art machinery to service all types of drive shafts, from small cars to race cars. They serve a variety of needs, including racing, industry and agriculture. Whether you need a new drive shaft or a simple adjustment, the staff at CZPT can meet all your needs. You’ll be back on the road soon!

U-joint

If your car yoke or u-joint shows signs of wear, it’s time to replace them. The easiest way to replace them is to follow the steps below. Use a large flathead screwdriver to test. If you feel any movement, the U-joint is faulty. Also, inspect the bearing caps for damage or rust. If you can’t find the u-joint wrench, try checking with a flashlight.
When inspecting U-joints, make sure they are properly lubricated and lubricated. If the joint is dry or poorly lubricated, it can quickly fail and cause your car to squeak while driving. Another sign that a joint is about to fail is a sudden, excessive whine. Check your u-joints every year or so to make sure they are in proper working order.
Whether your u-joint is sealed or lubricated will depend on the make and model of your vehicle. When your vehicle is off-road, you need to install lubricable U-joints for durability and longevity. A new driveshaft or derailleur will cost more than a U-joint. Also, if you don’t have a good understanding of how to replace them, you may need to do some transmission work on your vehicle.
When replacing the U-joint on the drive shaft, be sure to choose an OEM replacement whenever possible. While you can easily repair or replace the original head, if the u-joint is not lubricated, you may need to replace it. A damaged gimbal joint can cause problems with your car’s transmission or other critical components. Replacing your car’s U-joint early can ensure its long-term performance.
Another option is to use two CV joints on the drive shaft. Using multiple CV joints on the drive shaft helps you in situations where alignment is difficult or operating angles do not match. This type of driveshaft joint is more expensive and complex than a U-joint. The disadvantages of using multiple CV joints are additional length, weight, and reduced operating angle. There are many reasons to use a U-joint on a drive shaft.
air-compressor

maintenance interval

Checking U-joints and slip joints is a critical part of routine maintenance. Most vehicles are equipped with lube fittings on the driveshaft slip joint, which should be checked and lubricated at every oil change. CZPT technicians are well-versed in axles and can easily identify a bad U-joint based on the sound of acceleration or shifting. If not repaired properly, the drive shaft can fall off, requiring expensive repairs.
Oil filters and oil changes are other parts of a vehicle’s mechanical system. To prevent rust, the oil in these parts must be replaced. The same goes for transmission. Your vehicle’s driveshaft should be inspected at least every 60,000 miles. The vehicle’s transmission and clutch should also be checked for wear. Other components that should be checked include PCV valves, oil lines and connections, spark plugs, tire bearings, steering gearboxes and brakes.
If your vehicle has a manual transmission, it is best to have it serviced by CZPT’s East Lexington experts. These services should be performed every two to four years or every 24,000 miles. For best results, refer to the owner’s manual for recommended maintenance intervals. CZPT technicians are experienced in axles and differentials. Regular maintenance of your drivetrain will keep it in good working order.

2018 China China made professional customized different shape spur gear and shaft – Supplier Manufacturer wholesaler Factory

2018  China China made professional customized different shape spur gear and shaft - Supplier Manufacturer wholesaler Factory

For more details.: Cell/Whatpp: +8613083988828

Cat three Stage Hitch How do I work the PTO on my tractor? Prior to operating the PTO, you will need to have your tractor to reach the starting up RPM (revolutions for every moment). After the starting RPM has been achieved you can commence working the PTO.EPG is a foremost producer and exporter of Solid Flanges as for each ANSI and ASME specifications.We offer you OEM provider. Our merchandise are marketing effectively in Chinese markets and some goods offered in intercontinental markets are properly received by Chinese and international consumers at residence and overseas.

Overview

Quick Particulars

Relevant Industries:

Production Plant

Manufacturer Name:

OEM

Merchandise NO:

SYF

Product Identify:

Steel Spur Equipment

Shade:

Black

Software:

Transmission Gearbox

Title:

High Precision General Motor Gear

Floor treatment method:

Carbonization

Processing:

CNC Machining

Certificate:

ISO9001

Dimensions:

Customer’s Drawing

Item:

OEM Precision CNC Machining

Provide Capacity

Provide Potential:
ten thousand Piece/Pieces per 7 days

Packaging & Shipping

Packaging Information
wooden box
Port
Shang hai

Online Customization

Item Description

A lot more than 15 many years adept technology and knowledge of us will give powerful support for the equipment you require.
Specially at warmth remedy, the code procedure of all, we have exceptional operating flow and standard to guarantee the toughness, making items reputable enough for making use of.
We sincerely hope setting up prolonged and welcoming enterprise relations with consumers from all over the entire world. Our objective is not just offering solution,
but also supplying a total remedy including product design, tooling, fabrication and services for our customers to obtain their upmost pleasure. 

Product identify

  Customized spur gear

essential phrase

hard tooth surface,plate shaftparts

Transient description  

GB3478 8h, for mining equipment

Tooth profile

involute

Material

42CrMoA

Process

forging+quenching&tempering+hobbing splines 

Strain angle

20° 

Model

Mn=four,Z=36,a=20° 

Authentic place

jiangsu,china

Solution

Factory direct sale C45 Normal Steel Chain Sprocket

Teeth

9T- 120T

Sprockets Type

Variety A sprockets :Plate (with out Hub)

Variety B sprockets:A single facet with hub

Kind C sprockets: Double side with hub

Completed bore sprockets:With the inner hole ,keyway and screw

Sprockets Size 

ANSI: 25/35/forty one/40/50/sixty/eighty/100/one hundred twenty/one hundred forty/a hundred and sixty/a hundred and eighty/two hundred/240

DIN/ISO:04C/06C/085/08A/10A/12A/16A/20A/24A/28A/32A/36A/40A/48A

DIN/ISO:04B/05B/06B/08B/10B/12B/16B/20B/24B/28B/32B/36B/40B/48B/56B,

Matrial:

Alloy Metal, Carbon Steel, Stainless Metal,Aluminum, Copper, Brass

Sprockets Measurement

ANSI: 25/35/forty one/40/50/sixty/eighty/one hundred/one hundred twenty/140/one hundred sixty/180/two hundred/240

Heat Treatment method

Hardening and Tempering, Substantial Frequency Quenching, Carburizing Quenching

Floor Therapy

Galvanizing/Zinc Plating, chrome plated, Black oxide Therapy

Process

Forging, Hobbing, Precision machining,

OEM

Supported

Primary Characteristics

» Severe uncooked substance inspection
» Stringent management above the complete producing process
» Sampling of all the goods right after last inspection just before cargo
» Good quality trace soon after shipping and delivery

Our Business

HangZhou EPT Group – a single of the most significant gearbox producer in China – Electromechanical Facilities Co. Ltd

HangZhou EPT Team – one particular of the largest gearbox producer in China – Electromechanical Products Co., Ltd.is a gift company integrating growth, design and style, creation and revenue,Main promoting goods contain gearbox motor,water pump,development equipment and components,bearings,hardware and electrical gear,plastic products,Labour security equipment.Our business usually stick to the procedure notion which includes people-oriented, innovation as the soul,be ready for threat in times of peace, unremitting  …..  

Thorough Pictures

Software area

Product sales territory

Packing & Delivery

Packaging

Dimension

500 (L) * 500 (W) * four hundred (D)

Weight

one.2 T

Packaging Details

If export to european nations around the world,the wood box will be fumigated.If container is too tigher,we will use pe film for packing or pack it according to consumers unique ask for.

Packaging

Size

five hundred (L) * five hundred (W) * four hundred (D)

Bodyweight

1.2 T

Packaging Specifics

The normal package is picket box(Measurement: L*W*H). If export to european countries,the wooden box will be fumigated.If container is as well tigher,we will use pe movie for packing or pack it in accordance to clients specific request.

FAQ

Q1: Are you trading firm or manufacturer ?

A: We are a manufacturer in ZheJiang China.welcome to our manufacturing facility to have a go to.

Q2: How we select types and specs?

A:You can e mail us the collection identify & code (for example: WJ collection worm gearbox) as properly as need information, this sort of as motor electricity, output velocity or ratio, provider aspect or your application…as significantly info as possible. If you can provide some pictures or drawings, it is far better.

Q3: How is your value? Can you offer any price reduction?

A: We will give the greatest price tag we can base on your wants and the portions.

This fall: How extended must I hold out for the suggestions after I send the enquiry?

A: In twelve several hours.

Q5: What is your item warranty interval?

A:We supply one particular yr warranty considering that the vessel departure date still left China.

Q6: What industries are your gearboxes being utilized?

A:Our gearboxes are commonly utilized to metallurgical tools, mining gear, automation gear, meals machinery, packaging products, tobacco tools and many others.

Speak to us

Mobile: +86-13083988828 we chat # or 0086-571-88220971 (WeChat)
E-mail:hzptcorp (a) gmail.com
Fax:+86-571-88220972
Include:No.789 ShenHua Road, , XiHu District, HangZhou, ZheJiang, China

EPG – one particular of the biggest transmission factory in China, principal merchandise: worm geared motors, agricultrual gearbox, planetary gear generate, helical,screw, beve gears and spare areas and agricultural parts manunfacuter in China /For far more details.: Cell/Whatpp: +8613083988828

2018  China China made professional customized different shape spur gear and shaft - Supplier Manufacturer wholesaler Factory